HOW TO: Check, repair and tune your MK2/Corrado 1.8 16v

Discussion in '16-valve' started by rubjonny, Jul 16, 2009.

Page 3 of 3
  1. rubjonny

    rubjonny Administrator Staff Member Admin

    Joined:
    Oct 31, 2003
    Likes Received:
    3,318
    Location:
    Bracknell
    updated with fuel injector test info :)
     
    rubjonny, Nov 29, 2013
    #41
  2. STEREOFLAVER

    stereoflaver New Member

    Joined:
    Mar 20, 2008
    Likes Received:
    0
    stereoflaver, Jan 29, 2014
    #42
  3. KARMANNSKI

    karmannski New Member

    Joined:
    Apr 7, 2015
    Likes Received:
    2
    Hi I wonder if there is other link with the guide for the 2.0 9a engines for corrado of how to tune it
    this one is not worrking
     
    karmannski, Apr 7, 2015
    #43
  4. rubjonny

    rubjonny Administrator Staff Member Admin

    Joined:
    Oct 31, 2003
    Likes Received:
    3,318
    Location:
    Bracknell
    rubjonny, Apr 7, 2015
    #44
  5. PINGMAN

    pingman New Member

    Joined:
    Jul 21, 2015
    Likes Received:
    1
    I have both these problems; odd occasional random miss/hold-back and my tacho drops straight past 2/3k down to ~1000 (occasionally dies) with a fast fall.

    No leaks on the the over-run valve piping that I can see.
    I've electrically charged it and it audibly clicks.
    I have good ign live on the yellow/black wire.
    As far as I can tell; no switched earth on the brown/black (BUT i'm not sure in what situation it should have a signal?? at idle from cold start?)

    Is it likely my ISV control unit is dead?
    Presumably that would be the likely culprit for the hunting and rich idle I have too?
     
    pingman, May 13, 2018
    #45
  6. rubjonny

    rubjonny Administrator Staff Member Admin

    Joined:
    Oct 31, 2003
    Likes Received:
    3,318
    Location:
    Bracknell
    the brown.black is triggered when you lift off from high rpm by the isv controller, have a look at the red/black wire from the controller to the spade connector near the coil and check the brown/white wires to the head as one of them is for the isv module
     
    rubjonny, May 14, 2018
    #46
  7. PINGMAN

    pingman New Member

    Joined:
    Jul 21, 2015
    Likes Received:
    1
    So If I rev it up to 5000 and let off the throttle I should see continuity with body earth on the black brown?
    could you advise what/how should I check the other two?
     
    pingman, May 14, 2018
    #47
  8. rubjonny

    rubjonny Administrator Staff Member Admin

    Joined:
    Oct 31, 2003
    Likes Received:
    3,318
    Location:
    Bracknell
    yep. easy to check the brown/white is good just check for ignition voltaghe between the black wire and the brown/white on the isv controller plug, for the red/black check for continuity between the isv pin and the coil negative :)
     
    rubjonny, May 15, 2018
    #48
  9. WONE

    wone New Member

    Joined:
    Sep 23, 2021
    Likes Received:
    0
    thank you
     
    wone, Sep 23, 2021
    #49
  10. GVK

    GVK Paid Member Paid Member

    Joined:
    Oct 23, 2003
    Likes Received:
    692
    Location:
    Lincs.
    Rubber Jonny is mentioned here :p

     
    GVK, Aug 26, 2022
    #50
    rubjonny likes this.
  11. rubjonny

    rubjonny Administrator Staff Member Admin

    Joined:
    Oct 31, 2003
    Likes Received:
    3,318
    Location:
    Bracknell
    Finally! My big break, I have arrived :lol:
     
    rubjonny, Aug 26, 2022
    #51
    costel1969, GVK and AKAeddypeck like this.
  12. GVK

    GVK Paid Member Paid Member

    Joined:
    Oct 23, 2003
    Likes Received:
    692
    Location:
    Lincs.
    Check the comments, in a moment of confusion he thought that I was Rubjonny lol
     
    GVK, Aug 26, 2022
    #52
  13. ZACMK2

    Zacmk2 New Member

    Joined:
    Sep 11, 2016
    Likes Received:
    0
    hey guys hope everyone is well.

    Read this thread thoroughly an is very helpful.

    when i disconnect the black and red to the isv. my kr wont start one bit. any ideas. only just bought the old girl the other day and she is low on power and idling poorly.
     
    Zacmk2, Mar 9, 2023
    #53
  14. rubjonny

    rubjonny Administrator Staff Member Admin

    Joined:
    Oct 31, 2003
    Likes Received:
    3,318
    Location:
    Bracknell
    wind out the idle screw a bit that should hopefully get it going
     
    rubjonny, Mar 9, 2023
    #54
Page 3 of 3

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...
    Dismiss Notice